Install the LED tube light often appear problems in the construction

In the actual installation link of LED tube light, often there are a number of construction problems, greatly influenced the final acceptance of the effect. In this for the led downlights installation construction of several major problems in the main, a detailed analysis and provide a solution. Bring down lamp installed this problem a: installation of lamps and lanterns is not in conformity with the requirements 1, ( l） Lamp installation deviation, not on the center point. （ 2) The levelness of the rows of lamps and lanterns, the straightness deviation is bigger. （ 3) Jane lamp hole greatly smallpox condole top, not neat. 2, root cause analysis ( l） Embedded lamp box when the position is wrong, there is deviation, install lamps and lanterns without to take remedial measures. （ 2) Construction personnel is not strong sense of responsibility, construction and acceptance of the existing norms, quality inspection evaluation standard are not familiar with. ( 3) Buyer buy lamps and lanterns and make xuan, ignoring quality; ( 4) led downlights was not set well hole size, hole, round hole diameter is not unified, etc. 3, preventive measures, l） Before install lamps and lanterns, should seriously find center, rectify the deviation. （ 2) Strictly regulate lamp hole position deviation degree, the rows of lamps and lanterns installation deviation should not be greater than 5 mm, therefore, need to stay in the construction of localization, the lamps and lanterns in vertical, horizontal, oblique and Lord with low levels are in a straight line. （ 3) Smallpox condole top LED downlight opening to set coordinates, in addition to the required straight, neat and equally, the size of the hole should conform to the specifications of the canister light, not too big, to ensure that the outer ring when the tube lamp installed firmly against condole top, not crack. （ 4) Construction personnel, procurement staff to carefully implement the relevant state and local regulations. Problem two: the installation of embedded parts, lamps and lanterns is fixed do not conform to the requirements 1, ( 1) LED tube light, embedded parts in too deep, different level; Mask there is crack between the wall and the calibre of the lamps and lanterns, lac pollution, not flat. （ 2) Between the lamp body and the ceiling with mortar, not clean up debris. （ 3) LED tube light, fixed bolt is loose. 2, root cause analysis ( 1) Embedded box without reliable fixation, template expansion mode, installation time coordinates are not accurate. （ 2) Construction personnel is not strong sense of responsibility, the use of electrical safety importance understanding insufficiency, convenience, and there is no clear mortar sundry. （ 3) The unreasonable lamp technology, no accurate reliable fixed box. 3, preventive measures, 1) When embedded box is deep, should be equipped with a box. To horizontal flat vertical installation of embedded parts, the application level calibration level, ensure the installation height of unity. After installation of lamps and lanterns to full seams, cannot leave gaps, completes the lights around the mask cleaning and protection. （ 2) Ensure clean the lamp body and mortar between condole top, not have a foreign body. （ 3) To solid tube lamp installation, single conductor when the insert line hole should be spread into twin, screw tight, tight. In order to ensure safety, it is recommended to use with a ring of the canister light diffusion interface card. Indeed, canister light card buckle quality in design is crucial, because of damage to install card buckle scrap tube light is countless. Therefore, in the selection, you should choose the high quality, secure the installation structure of the LED spotlights. You both in the face of the airport terminal building, hotel, office, or shang chao deng lighting project, for the ceiling zone using LED tube light to open hole arrangement this link, must pay attention to considering the above problems, completes the prevention measures, to ensure the smooth construction.
Foshan Rayven Lighting Co., Ltd has various branches in different countries worldwide.
Our knowledgeable loss prevention experts can help commercial customers reduce losses in INFO CENTER.
Foshan Rayven Lighting Co., Ltd clearly knows that people often launch something and love it and want to go on and on about it, but that's too normal and mediocre. There are lots of other competing products, so we need to keep it very, very unique.